On stock

APM CNC tube rings, 145mm, price for one pc

Item condition: new and original packed

APM CNC tube rings for tube diameter 170 mm, price each set

Item condition: new and original packed

APM-JK CNC-tube rings for tube diameter 300mm Stable, easily swivelling open metal clamps for an optimal connection between telescope and mount. Suitable for telescope tubes with 300 mm outer diameter Easy and quick mounting of the rings to the telescopes Felt coating at the inner side prevents from scratches on the tube

Item condition: new and original packed

Product description Classy CNC Tube Rings with elegant design and uncompromising quality A beautiful telescope should be attached to the mount with perfect tube rings, too. Here, a beautiful look is as much in demand as gut technical properties. The CNC tube rings fulfill these requirements. The tube has only 8 mm distance to the bottom side of the rings, thus the mount is not additionally loaded by unnecessarily long levers. The tubes have plane support surfaces on both sides with five female M6 threads on each side. 1 M6 thread in the middle, 2 M6 threads at a distance of 19 mm from the middle, 2 M6 threads at a distance of 30mm from the middle. With this, you can easily attach dovetail bars and accessories. With only 5 mm thickness, the rings are lightweight yet very stable A thin layer of felt was put on the inside of the tube rings for avoiding scratches. However, the tube is clamped very well in the rings and does not change position. That is important if a guiding scope is attached to the rings. Delivery contents Set of 2x Aluminium CNC Tube Rings

Item condition: new and original packed

Classy CNC tube rings with elegant design and uncompromising quality from TS Optics A beautiful telescope should be attached to the mount with the finest tube ring. Here, a beautiful appearance is as important as good technical properties. The CNC tube rings from TS meet these requirements. ♦ The tube is attached to the mount or the dovetail via a largely dimensioned support surface. ♦ The rings have identical support surfaces on top which allows attaching dovetail clamps or another dovetail bar. ♦ The rings can be folded open, thus the telescope can be removed from them within seconds. ♦ A thin layer of felt was applied to the inner side of the rings. This prevents from scratches. Nevertheless, the telescope tube is clamped very well in the rings and does not misalign. This is important if a guiding scope is attached to the rings. ** 1 Piece **

Item condition: new, but not original packed

Baader T2 Extension Tube #25A, Length 15 mm

Item condition: new, but not original packed

ASI T2-Tilter - Tilt flange Adjustment of image plane and sensor position Many astrophotographers know the problem: You focus as good as possible and in 1-2 corners the sharpness is still not satisfying. The result is a bad compromise, by changing the sharpness setting until the stars appear relatively evenly "sharp" or by simply cutting away the corner. Some possible causes of this problem: ♦ a slight tilt of the camera sensor (only a few fractions of a millimeter are enough) ♦ a tilt of the focuser ♦ a slight tilt of the field plane of the telescope (very common with Newtonian telescopes) ♦ a tilting of the eyepiece-side accessories during clamping This is the solution: With the ASI T2 tilter you simply adjust the chip of the camera to the field of the telescope, no matter where the cause of the tilt comes from. You only have to keep the orientation of the whole adapters, correctors and camera. Connecting the camera to the tilter: In principle, any suitable camera can be connected to the tilter via the T2 thread. However, additional bores also allow the connection directly to the camera body on the following ZWO cameras: ♦ ASI294/ASI1600/ASI183/ASI533 Pro cooled ♦ ASI294/ASI1600/ASI183/ASI174 uncooled With the ASI071 and ASI 2600 Pro the housing is differently dimensioned, the direct connection does not work. There it only works via the T2 thread.

Item condition: new and original packed

TS Optics T2 focal adapter for Skywatcher focusers with female M54x1 thread

Item condition: new and original packed

This adaptor allows you to connect your Pentax SLR camera with the Pentax K and Sigma Bajonett to a telescope or spotting scope. The ring fits into the bayonet of the camera and has the T2 (T-Mount, M42x0.75) thread on the inside. You only need a T2 male thread on the telescope or spotting scope. We offer such adapters for most common telescope models. Three small headless set screws allow you to rotate the camera if needed.

Item condition: new and original packed

TS Optics Stainless steel fine tuning ring for T2-thread - thickness 0.3 mm

Item condition: new and original packed

Altair Nikon DSLR lens adapter for Hypercam fan cooled camera Attach your Altair Hypercam CMOS camera to a Nikon photographic lens for wide flat field astrophotography. You can insert 2" filters, too. Rotates for framing and you can move the adapter back and forth on the dovetail bar for balancing. On top of the adapter are two holes for mounting an universal guide scope bracket. Included is the adapter for Hypercam Fan-Cooled models with 12.5mm sensor to flange distance. Features Full frame clear aperture! Fits all Nikon F-mount bayonet lenses. Internal 2" filter mounting position for CLS filters, etc. Sealed chamber for dust control! Base has mounting stalk for back or forwards attachment to 200mm dovetail plate - enabling balance even with large lenses. Includes standard 200mm dovetail bar with multiple 1/4" M6 holes and slots. Holes for mounting an universal guide scope bracket. Delivery contents Nikon lens adapter Adapter for Hypercam fan cooled models

Item condition: new and original packed

Celestron # 93418 T-Ring Canon EOS

Item condition: new and original packed