Secondhand & Stock

ASI T2-Tilter - Tilt flange Adjustment of image plane and sensor position Many astrophotographers know the problem: You focus as good as possible and in 1-2 corners the sharpness is still not satisfying. The result is a bad compromise, by changing the sharpness setting until the stars appear relatively evenly "sharp" or by simply cutting away the corner. Some possible causes of this problem: ♦ a slight tilt of the camera sensor (only a few fractions of a millimeter are enough) ♦ a tilt of the focuser ♦ a slight tilt of the field plane of the telescope (very common with Newtonian telescopes) ♦ a tilting of the eyepiece-side accessories during clamping This is the solution: With the ASI T2 tilter you simply adjust the chip of the camera to the field of the telescope, no matter where the cause of the tilt comes from. You only have to keep the orientation of the whole adapters, correctors and camera. Connecting the camera to the tilter: In principle, any suitable camera can be connected to the tilter via the T2 thread. However, additional bores also allow the connection directly to the camera body on the following ZWO cameras: ♦ ASI294/ASI1600/ASI183/ASI533 Pro cooled ♦ ASI294/ASI1600/ASI183/ASI174 uncooled With the ASI071 and ASI 2600 Pro the housing is differently dimensioned, the direct connection does not work. There it only works via the T2 thread.

Item condition: new and original packed

TS Optics T2 focal adapter for Skywatcher focusers with female M54x1 thread

Item condition: new and original packed

This adaptor allows you to connect your Pentax SLR camera with the Pentax K and Sigma Bajonett to a telescope or spotting scope. The ring fits into the bayonet of the camera and has the T2 (T-Mount, M42x0.75) thread on the inside. You only need a T2 male thread on the telescope or spotting scope. We offer such adapters for most common telescope models. Three small headless set screws allow you to rotate the camera if needed.

Item condition: new and original packed

TS Optics Stainless steel fine tuning ring for T2-thread - thickness 0.3 mm

Item condition: new and original packed

Altair Nikon DSLR lens adapter for Hypercam fan cooled camera Attach your Altair Hypercam CMOS camera to a Nikon photographic lens for wide flat field astrophotography. You can insert 2" filters, too. Rotates for framing and you can move the adapter back and forth on the dovetail bar for balancing. On top of the adapter are two holes for mounting an universal guide scope bracket. Included is the adapter for Hypercam Fan-Cooled models with 12.5mm sensor to flange distance. Features Full frame clear aperture! Fits all Nikon F-mount bayonet lenses. Internal 2" filter mounting position for CLS filters, etc. Sealed chamber for dust control! Base has mounting stalk for back or forwards attachment to 200mm dovetail plate - enabling balance even with large lenses. Includes standard 200mm dovetail bar with multiple 1/4" M6 holes and slots. Holes for mounting an universal guide scope bracket. Delivery contents Nikon lens adapter Adapter for Hypercam fan cooled models

Item condition: new and original packed

TS - Adapter of the standard T-2 thread (M-42 x 0.75) on 2" The adapter allows connecting 2" accessories to devices or adapters with T2 connection: - Telephoto lenses - Focusers with T2-thread - Adapters with male T2-thread The adaptor can easily be screwed onto any T2 male thread. The 2" accessory is clamped via a brass compression ring and thus over a large area, thus pressure marks or tilting are avoided.

Item condition: new and original packed

TS Optics Adapter ring from M48 to Sony Alpha / Minolta AF A bayonet Offers more free aperture than T2 for less vignetting This short M48 adapter (2" filter thread) to Sony A/Minolta bayonet offers an optimal adaption to M48 without the T2 bottleneck thus improving the field illumination, even with full-format DSLR cameras. The T-Ring adapter fits to: All Sony Alpha / Minolta AF (D)SLR cameras with A-mount This T ring does not work with Sony E-mount cameras! On the telescope side, it e.g. fits to: Skywatcher field flattener / reducser for ED refractors (SKFlat80, SKFlat100, SKFlat120) Skywatcher coma correktor (Komakorrf4) Baader MPCC Koma Corrector TS Newton Koma Korrector (TSKomakorr) TS, Riccardi, TeleVue ... Flattener and correctors 2" telescope adaption offering full aperture With an M48 extension tube, you can turn this T-ring to short bayonet adapter to 2" offering full aperture. Delivery contents Sony Alpha adapter

Item condition: new and original packed

TS Optics 3mm extension with M48 - 2" filter thread and 2" diameter

Item condition: new and original packed

M48 Extensiontube 8mm

Item condition: new and original packed

TS Optics Adaptor M42x1 female / EOS EF Bayonet with 0 mm optical length This adaptor screws directly into the Canon EOS body and enables you to connect objectives with M42x1 thread. Please note: The adapter does NOT work with M42 lenses with a very large diameter, e.g. MTO1000, Rubinar 500 and Rubinar 300

Item condition: new and original packed

Baader VariLock 29 - locakble variable T2 extension 20-29 mm (T2 part #25Y)

Item condition: new, but not original packed

Product description TS Optics Off Axis Guider with Zeiss M68x1 connection - short design Off axis guider for large cameras This big off axis guider with Zeiss M68 thread connection is a consequent further development of the short TSOAG9. This model is designed for heavy cameras with large sensors. With an optical length of 16.7 mm, it also needs not much back focus. But nevertheless, it offers all options needed for professional tracking. Advantages and characteristics M68x1 Zeiss thread on both sides Length 16.7 mm only (w/o male threads) Choice of three positions (120° each) for the sidewards T2 guiding cam adapter, thus you have always a good framing option for the sensor Free aperture of 62.5 mm: even large camera sensors can be used without vignetting Massive design: all connections are screwed, no clamping. This is ideal for heavy cameras. The guiding focus can be adjusted individually The prism can be shifted in order to reach an optimal position relative to the main sensor Internal surface with anti-reflective thread Three connections for the prism tower Due to the massive design, this OAG has no rotation functionality that could compromise the solid connection of heavy cameras. Three positions (3 x 120°) can be used for the guiding tower. Inappropriate prism positions relative to the main sensor (e.g. in front of an edge) are prevented. If the guiding cam collides in one position with the main camera, another position can be chosen. The two holes not in use can be closed to prevent stray light from entering the system. Short design The off axis guider is consequently designed for short design without compromising its stability or ease of use. All elements can also be operated when wearing gloves. Distances to prism Distance from female M68 thread to prism center: 11.5 mm Minimum distance from prism center to T2 thread: 27 mm Delivery contents Off axis guider

Item condition: new and original packed